Posts Tagged ‘mixer’
Mixer Stage Cable
November 3rd, 2010Main Stages of Repair Works in the Apartment
How to begin repair works of the apartment?
The first stage of the repair of old apartments is the destruction and dismantling first of all of the dilapidated walls and partition walls, removing the wall and ceiling coating. This stage is one of the most “dirty” stages of the repair.
One more among the most important and “dusty” works is the window block replacement. It is necessary to do this first of all because dirt and dust will be unallowable during following stages and it is prohibited at all to open windows during painting and wallpaper works (large drops of the temperature and moisture are unallowable). After mounting windows and windowsills it is necessary to pack them immediately in polyethylene film and to cover windowsills in addition by the fiberboard (in order to prevent scratches).
The following stage is wiring. Wiring can be installed in walls or along the floor. Wiring is made inside the pipes to ensure electrical safety and increase reliability. The pipe protects wiring from external damages and allows to replace the wire completely without breaking walls and floor simply by inserting the new wire instead of the old one.
House Painting follows the wiring. The frequent mistake during the simultaneous conducting of such works occurs when workers forget to lay out one of the cables and house painters have already plastered and smoothed out the wall. As a result, additional works are necessary to seal chases on the finished wall. The places of the feed switch and wall outlet location and their number must be thought-out in advance. The scheme of power wiring is usually included into the design project.
Later on the system must be ready to service in case of failures. In addition to the wirings, the telephone cable and the TV cable are laid out. The power cable should not be laid out near the telephone and antenna cables to avoid noise pickup and interference. The most peculiar moment is laying out the TV cable. In order to make two (or three) TV sets in the apartment the second cable is often simply “firmly soldered” in parallel, so the cable resistance is lowered. As a result, the display quality is deteriorated, many programs can’t be received and etc. In order to avoid such situation it is necessary to invite a specialist with special equipment. He will measure the signal level of the each TV-feeder and install TV-amplifiers or TV-filters.
Painting is the most long-term process, that is why it is conducted simultaneously in all premises, if it is possible. Delays are linked with the technology. Each applied layer of the plaster (or filling in finishing) must dry completely before the work will continue.
Works in sanitary arrangements and the kitchen begin simultaneously with house painting. It is better to fulfill so-called “dirty” works in the first place and simultaneously. In accordance with the plan of the sanitary technician location welding, wall chasing and pipe run are conducted. Steam radiator admissions are prepared, taps and brackets are mounted, but radiators are not installed.
Then works in sanitary arrangements are conducted according to the plan. The bath is mounted, then walls are smoothed out and the tile is laid on walls. The following stage is assembling ceiling and laying tiles on the floor. And at last other sanitary devices, mixers and accessories are mounted.
After wiring, installation of rosette plates and terminal boxes the voltage is checked in all point. Ends of wiring are insulated and laid out into rosette plates. Sockets and breakers are not installed during this stage in order to save their surface appearance. The finish puttying of walls is conducted simultaneously. The technologically exact control of drying of the layer of the plaster (filling) is carried out by drymeter. It is a special instrument that measures moisture of the material.
The following stage is the process of fill. Fill can be made with different materials – from usual masonry cement-sand mixture to self-aligning floors. The advantage of the simple mixture is its cheapness, the disadvantage is that such mixture is much harder aligned at the level and the final dry time of such fill is 40 days, only then the next stage of the work with floor can be conducted, i.e. the period is too long. Self-leveling self-aligning floors are much more expensive, but more technological. Aligning occurs almost “automatically” i.e. fluid solution of mixture is poured out, then it runs and you receive the horizontal surface. The final dry time is 15 days i.e. you have significant time economy. The system “warm floor” is installed into the fill. If the so-called “wet processes” are inapplicable the technology of the dry aligning (the fill technology) is used bases for floors with adjustable floor battens are mounted.
After fill door boxes and door are installed. Installation of doors must take into the account thickness of future floor covering. After installation the door can be taken off its hinges and removed until the end of repair or packed into polyethylene film to protect from damages. Simultaneously ceiling can be painted and the tile can be laid in that premises where it was planned. The tile must be laid on the absolutely dry overlay.
Finishing of the floor mounting depends on the planned covering. In most cases (if finish covering is not the tile) fill is covered by bitumen mastic and plywood sheets are laid. They are fixed to the floor by self-tapping screws. One plywood sheet is fixed by 30-50 self-tapping screws to provide the close fixing of plywood and long-term service of the floor without squeak and bulging. The plywood gives the additional heat- and acoustic insulation. After mounting of the plywood is finished, wallpaper for painting can be pasted on walls.
In premises where finish covering of the floor is laminated flooring or parquet hoard, the ordinary wallpapers are pasted (not for painting) in the first place. Then the floor covering is mounted.
If finish covering of the floor is the block parquet, the parquet is laid in the first place, then it is scraped and covered by one layer of lacquer. After this the ordinary wall-papers are pasted and the parquet is covered by the rest layers of lacquer (depending on the quality of the parquet and lacquer). The mentioned consequence is linked only with such scrambling process when the great amount of dust is created. In spite of the fact that good floor grinders are equipped with the vacuum cleaner, the sufficient amount of dust is precipitated on surrounding subjects including walls. Dust is very acerbic and is badly washed off. That is why in order not to damage wallpapers, they are pasted after scrambling and in order the parquet do not absorb the surplus moisture it is covered by the one layer of lacquer before wallpaper pasting.
After this the main works can be considered to be finished. It is left only to install the plinths, decorative elements, breakers and sockets, curtain holders, to hang doors, plant-bands and others.
In conclusion it is necessary to note that the sequence of works was listed in general and can change depending on the definite situation – the number of rooms in premise, your resources, peculiarities of the construction of the multilevel premises. It is based on common sense and every person capable of analysis can independently create such a sequence.
© Copyright 2006-2007 www.builderstown.co.uk
About the Author
Arthur Prudent is a developer of London builders: kitchen, bathroom renovation – web site offering all aspects of builders services. Find Home Improvement articles at “Useful Tips”
Stage Cables (A tip for diagnosing Problems)
Tripp Lite APS3636VR 3600W 36V DC to AC Inverter with Automatic Line-to-Battery 30-Amp Charger $1,531.80
36V DC – 120V AC – Continuous Power:3600W…
Click here to learn more about Tripp Lite APS3636VR 3600W 36V DC to AC Inverter with Automatic Line-to-Battery 30-Amp Charger
Tripp Lite APS2012 2000W 12V DC to AC Inverter with Automatic Line-to-Battery 100/25-Amp Charger $1,089.00
Tripp Lite APS2012 PWRINV APS 2012 2000W 12VDC HWIRE…
Click here to learn more about Tripp Lite APS2012 2000W 12V DC to AC Inverter with Automatic Line-to-Battery 100/25-Amp Charger
Tripp Lite APS750 750W 12V DC to AC Inverter with Automatic Line-to-Battery 20-Amp Charger $289.46
12V DC, 120V AC – 120V AC – Continuous Power:750W…
Click here to learn more about Tripp Lite APS750 750W 12V DC to AC Inverter with Automatic Line-to-Battery 20-Amp Charger
Tripp Lite APS700HF 700W 12V DC to AC Inverter with Automatick Line-to-Battery 20-Amp Charger $304.99
The TrippLite 700W 12V DC to AC Inverter has a versatile inverter/charger system with auto-transfer switching serves as an automotive inverter for RVs, over-the-road trucking, conversion vans and fleet service vehicles. The TrippLite 700W 12V DC to AC Inverter has a standalone alternative power source for off-grid, alternative energy or export applications and as an uninterruptible power supply (U…
Click here to learn more about Tripp Lite APS700HF 700W 12V DC to AC Inverter with Automatick Line-to-Battery 20-Amp Charger
Tripp Lite APS2448UL 2400W 48V DC to AC Inverter with Automatic Line-to-Battery 15-Amp Charger $1,261.80
Tripp Lite”s APS2448UL DC-to-AC inverter with automatic line-to-battery transfer and integrated charging system serves as an extended run UPS, a standalone power source or an automotive inverter. Supplies up to 4800 watts of continuous 120V AC power from any 48V DC bus or battery source. Floating 48VDC ground offers compatibility with positive or negative grounded DC systems, including 48V telco …
Click here to learn more about Tripp Lite APS2448UL 2400W 48V DC to AC Inverter with Automatic Line-to-Battery 15-Amp Charger
On-Stage RS9050 Adjustable Amplifier and Mixer Stand $94.95
The On-Stage RS9050 Adjustable Amplifier and Mixer Stand is a project studio utility stand with the perfect solution for today’s musician. A versatile design, this all-steel heavyduty stand features an adjustable tilt top platform, built-in outboard gear rack and a set of sturdy locking casters.
Click here to learn more about On-Stage RS9050 Adjustable Amplifier and Mixer Stand
On-Stage MIX400 Autolocator and Mixer Stand $99.95
Ideally suited for home, project, multimedia and professional recording studios — this is the perfect rolling companion to your control surface, BRC, etc. It’s completely adjustable — platform width, height, tilt angle — making it one of the most flexible tools in your studio. Holds a wide variety of multitrack recorders, mixers, remote controllers, and more.
Click here to learn more about On-Stage MIX400 Autolocator and Mixer Stand
Samson SM10 Line Mixer $199
Ideal for stage, studio and an infinite variety of installation applications, Samson’s SM10 Line Mixer is a versatile and reliable addition to your audio setup. This internally powered, 19-inch rackmount metal chassis unit can be easily integrated into any existing system to more efficiently group your signals.
Click here to learn more about Samson SM10 Line Mixer
Mackie 1202VLZ3 12-Channel Mixer $269.99
Sure it’s cute, but the Mackie 1202VLZ3 is a serious professional compact mixer, with features that belie its small footprint. The ideal compact mixer for home and project studios, the 1202VLZ3 is equally at home on the road, on the stage, or in the recording studio. At Mackie, they can never leave “well enough” alone. After all, the VLZ Pros are the best-selling mixers of all time, so we knew it would be tough to improve on what many devoted owners already consider perfection… and yet they were driven to do it anyway.
Click here to learn more about Mackie 1202VLZ3 12-Channel Mixer
Sm Pro Audio Stage-Buddy Personal Monitor Mixer $329.99
This Remote unit for the SM Pro Audio Stage-Buddy System expands monitoring capabilities. The Remote monitor unit can be connected either directly to the Master unit or daisy-chained (up to 8 units) to each other in succession using readily available standard Cat 5 network cable. Bi-directional audio transmission and power is supplied to each remote unit directly from the Master, making an extremely simple and elegant solution for distributing personal monitoring to end-users.Each Remote unit is a little wonder in itself. With a host of features packed into a compact monitoring unit, the Remote offers quality personal microphone preamplification, EQ, Reverb, limiting, and a powerful, pristine headphone amplifier. The special and ingenious “More Me” control is a standout. What could be easier than simply turning up the More Me knob when wanting to listen to a little more of your own voice or instrument through a pair of headphones or monitoring amplifier?How about a little reverb on your voice, or would you prefer to wind back the top end a little? Simply dial it in on the front panel of the SM Pro Audio Stage-Buddy Remote. Dial in some reverb, dial in More Me, and you’re done.Whether you are using floor wedges, an in-ear system, or a pair of headphones to monitor your audio, the SM Pro Audio Stage-Buddy represents the next generation in personal monitoring control. Featuring onboard EQ, signal limiting, and a quality reverb, the Stage-Buddy provides a much-needed personal monitoring solution suitable for monitoring voice, guitar, or any line level or microphone signal.Personal audio monitoring has, for the main part, been limited in use due to both the prohibitive expense of available systems coupled with their excessively complex operation for untrained users. With the release of Stage-Buddy, personal monitoring is now accessible to the masses. The Stage-Buddy is not only affordable, but provides a much-needed solution in an easy-to-use package. The Stage-Buddy ushers in exciting innovations in personal monitoring.With the Stage-Buddy there is no longer a need for complex monitor mixing, multi-channel inputs, or complex monitoring configurations. Simply sending a stereo master mix feed from the front of house mix to the Stage-Buddy Master unit allows Remote users the ability to dial up their monitoring preferences without fuss.Monitoring options abound with the Stage-Buddy system. Whether you connect headphones, powered stage monitors, or in-ear monitoring systems, the Stage-Buddy has all options covered. It is ideal for a wide range of application environments like recording studios, broadcast facilities, live band venues, home studios, and orchestra pits.Consider personal monitoring for an entire orchestra. With the Stage-Buddy system, up to 16 units can be connected to a single Master unit. Each member of the orchestra could quickly control his or her own desired level and settings. Several Master units could also be cascaded to offer 128, 25
Click here to learn more about Sm Pro Audio Stage-Buddy Personal Monitor Mixer
Used Sm Pro Audio Stage-Buddy Personal Monitor Mixer 886830143687 $165
This Remote unit for the SM Pro Audio Stage-Buddy System expands monitoring capabilities. The Remote monitor unit can be connected either directly to the Master unit or daisy-chained (up to 8 units) to each other in succession using readily available standard Cat 5 network cable. Bi-directional audio transmission and power is supplied to each remote unit directly from the Master, making an extremely simple and elegant solution for distributing personal monitoring to end-users.Each Remote unit is a little wonder in itself. With a host of features packed into a compact monitoring unit, the Remote offers quality personal microphone preamplification, EQ, Reverb, limiting, and a powerful, pristine headphone amplifier. The special and ingenious “More Me” control is a standout. What could be easier than simply turning up the More Me knob when wanting to listen to a little more of your own voice or instrument through a pair of headphones or monitoring amplifier?How about a little reverb on your voice, or would you prefer to wind back the top end a little? Simply dial it in on the front panel of the SM Pro Audio Stage-Buddy Remote. Dial in some reverb, dial in More Me, and you’re done.Whether you are using floor wedges, an in-ear system, or a pair of headphones to monitor your audio, the SM Pro Audio Stage-Buddy represents the next generation in personal monitoring control. Featuring onboard EQ, signal limiting, and a quality reverb, the Stage-Buddy provides a much-needed personal monitoring solution suitable for monitoring voice, guitar, or any line level or microphone signal.Personal audio monitoring has, for the main part, been limited in use due to both the prohibitive expense of available systems coupled with their excessively complex operation for untrained users. With the release of Stage-Buddy, personal monitoring is now accessible to the masses. The Stage-Buddy is not only affordable, but provides a much-needed solution in an easy-to-use package. The Stage-Buddy ushers in exciting innovations in personal monitoring.With the Stage-Buddy there is no longer a need for complex monitor mixing, multi-channel inputs, or complex monitoring configurations. Simply sending a stereo master mix feed from the front of house mix to the Stage-Buddy Master unit allows Remote users the ability to dial up their monitoring preferences without fuss.Monitoring options abound with the Stage-Buddy system. Whether you connect headphones, powered stage monitors, or in-ear monitoring systems, the Stage-Buddy has all options covered. It is ideal for a wide range of application environments like recording studios, broadcast facilities, live band venues, home studios, and orchestra pits.Consider personal monitoring for an entire orchestra. With the Stage-Buddy system, up to 16 units can be connected to a single Master unit. Each member of the orchestra could quickly control his or her own desired level and settings. Several Master units could also be cascaded to offer 128, 25
Click here to learn more about Used Sm Pro Audio Stage-Buddy Personal Monitor Mixer 886830143687
Mogami Gold Stage Microphone Cable $83.95
Virtually every major recording facility in the world is wired with Mogami cable. This means that just about any music you choose has been recorded using Mogami in the audio chain. This cable is famous for unmatched accuracy, extremely low noise and remarkable flexibility. Top engineers rave about its amazing clarity and silent background. If accuracy in reproduction is your goal, this is the cable for you.
Click here to learn more about Mogami Gold Stage Microphone Cable
On-Stage CTA6600 Velcro Cable Ties $2.95
The perfect way to contain your unruly cables. Provides an easy, neat way to secure your guitar, mic and power cords. These fabric strips feature Velcro style closures to hold your coiled cables in place. Ties can remain on cable at all times.
Click here to learn more about On-Stage CTA6600 Velcro Cable Ties
Planet Waves American Stage Instrument Cable $19.95
Planet Waves American Stage Series cables are designed to reproduce the natural tones of your instrument with zero interference. Made in the USA with audiophile quality wire, the low 28pF/ft capacitance is the sweet-spot for uncolored tone and the 22AWG oxygen-free copper conductor provides exceptional signal transfer.
Click here to learn more about Planet Waves American Stage Instrument Cable
On-Stage GS7462B A-Style Folding Guitar Stand $18.95
An affordably priced A-Frame guitar stand for electric or acoustic guitars. This stand features a lightweight design, black velveteen rubber and On-Stage’s patented double-stepped yoke. It can also be used as a desktop mixer stand. Black finish.
Click here to learn more about On-Stage GS7462B A-Style Folding Guitar Stand
Alesis MultiMix 8 Line 8-Channel Mixer $199
MultiMix 8 Line is an ideal mixer for the stage, studio, boardrooms, conference rooms, health clubs, restaurants, houses of worship, and more. MultiMix 8 Line is also a great fit for any band’s live rig, especially for keyboard players and multi-instrumentalists who need to mix or sub-mix multiple sources.
Click here to learn more about Alesis MultiMix 8 Line 8-Channel Mixer
Mackie 1402VLZ3 14-Channel Mixer $399.99
Just slightly larger than Mackie’s 1202-VLZ3, the Mackie 1402-VLZ3 offers everything its little brother has-plus two additional mic/line channels, faders instead of knobs, and a few extra Master Section features. Ideal for home and project studios, the 1402-VLZ3 is equally at home on the road, on the stage, or in the recording studio. With its new look, ergonomic carry handle, and upgraded electronics, the new 1402-VLZ3 just might redefine the term “perfection.”
Click here to learn more about Mackie 1402VLZ3 14-Channel Mixer
Hot Wires Stage Snake $189.99
The Hot Wires Stage Snake Box provides XLR channels (XLR) female with XLR male returns and includes locking connectors with quick disconnect buttons for a secure fit. Also, each XLR connector is hand-soldered and individually insulated to ensure that no electrical shorts will occur. Other features include well-protected and flexible cable bundling and a heavy-duty metal chasis box. Comes with a built-in easy carrying handle and a black nylon protector bag.
Click here to learn more about Hot Wires Stage Snake
Nady Center Stage Microphone and Stand Kit $27.99
The Nady Center Stage Neo-dymium Dynamic Microphone is a versatile, professional microphone designed to provide top performance in all live performance, and public address applications. Its transparent sound also makes the Center Stage microphone a valuable recording tool. The mic kit includes a 20 ft. XLR to 1/4″ cable for connecting microphone to your audio mixer or amplifier, a secure grip microphone clip, and a sturdy metal tripod easily adjustable for performers up to 6′ 4″ tall.
Click here to learn more about Nady Center Stage Microphone and Stand Kit
On-Stage Stands Mix-400 Audio Mixer Stand $131.03
The On-Stage Stands Mix-400 mixer stand’s metal platform can adjust to fit any autolocator, drum machine, or digital audio workstation between 14-1/2″ and 21-1/2″ long and 12″ to 15-1/2″ wide. Double-spine gears with radial grooves allow the adjustable head to swivel in any position from fully horizontal to nearly vertical. Use the Mix-400 standing or sitting–the center shaft adjusts the height from 28″ to 38″ and can be friction-locked into place. High-impact plastic 5-leg base with fully lockable casters ensures the stand (and your equipment) will stay put. The Mix-400 breaks down into 3 pieces for simple storage and easy portability.
Click here to learn more about On-Stage Stands Mix-400 Audio Mixer Stand
On-Stage Stands Mix-400 Audio Mixer Stand 886830126697 $122.39
The On-Stage Stands Mix-400 mixer stand’s metal platform can adjust to fit any autolocator, drum machine, or digital audio workstation between 14-1/2″ and 21-1/2″ long and 12″ to 15-1/2″ wide. Double-spine gears with radial grooves allow the adjustable head to swivel in any position from fully horizontal to nearly vertical. Use the Mix-400 standing or sitting–the center shaft adjusts the height from 28″ to 38″ and can be friction-locked into place. High-impact plastic 5-leg base with fully lockable casters ensures the stand (and your equipment) will stay put. The Mix-400 breaks down into 3 pieces for simple storage and easy portability.
Click here to learn more about On-Stage Stands Mix-400 Audio Mixer Stand 886830126697
Hosa DOC106 Audio Direct Out Insert Cable $10.5
Beat the system! This slick little cable lets you use your mixer’s insert jacks as direct outs – for recording!
Click here to learn more about Hosa DOC106 Audio Direct Out Insert Cable
Odyssey FFXMIXBL Flight FX DJ Mixer Case $179.95
The Odyssey FFXMIXBL Flight FX DJ Mixer Case is truly a remarkable piece that is sure to turn some heads. Embedded into the case wall is a color changing multi-mode LED panel that runs across the front of the case. The panel can be set to any one of seven colors or can be set at a variety of color changing modes. For multiple case setups, any FX case can be synchronized to another by connecting the control boxes. Each Flight FX Series case is constructed with the same black anodized and powder coated black hardware as Odyssey’s Flight Zone Black Label cases, complimenting the visual aura of the glowing panel. Become center stage at any gig behind these cases. Innovating? Of Course! Another Spectacular original Odyssey Design. Just excellent!!!
Click here to learn more about Odyssey FFXMIXBL Flight FX DJ Mixer Case
Posted in Cables | 
Tags: camera, mixer, mixer stage cable, photo, photography, shopping, video | 
No Comments »